The decision on test bao 5 cabin climate and thermal performance stays attached to one selected VIN. Record identify installed equipment, record test conditions and test airflow and controls before comparing routes; keep test cooling and heating, review diagnostics and repair and plan destination operation visible through quotation and handover.
Continue the evidence route: Identify the powertrain in the DMO thermal-system guide, connect energy use to the range and fuel plan, and verify service support through maintenance planning.
Identify installed equipment
Match production version, climate zones, vents, heated or ventilated functions and thermal hardware to the VIN.
Evidence threshold. For identify installed equipment, Do not copy equipment from another Bao 5 edition. Link identify installed equipment to the VIN and source date. Name who checked identify installed equipment, and retain enough detail for another reviewer to reproduce the result.
Record test conditions
Capture ambient, cabin and battery conditions, state of charge, settings and vehicle operating mode.
Failure condition. For record test conditions, Make the result repeatable. If record test conditions stays open, specify whether to reject, reprice or reinspect. Do not treat seller silence about record test conditions as supporting evidence.
Test airflow and controls
Operate blower speeds, vent modes, recirculation, demist and rear functions while recording weak or inconsistent output.
Destination effect. Separate control behaviour from temperature performance. Ask the destination adviser whether test airflow and controls changes customs or registration. Check charging, road use and service separately when test airflow and controls affects them, then retain the dated response.
Test cooling and heating
Record time to useful response, sustained behaviour, warnings, odour, noise and visible drainage.
Cost effect. Stop for electrical or thermal warnings. Price test cooling and heating as its own inspection or preparation line. If test cooling and heating creates compliance risk, show the contingency clearly rather than burying it in a general discount.
Review diagnostics and repair
Preserve climate and thermal faults, front-impact evidence, lines, condenser, filters and prior service records.
Custody check. Use qualified procedures around refrigerant and high voltage. Reconfirm review diagnostics and repair at each custody transfer. Seller, inspector, transporter and port records for review diagnostics and repair should remain dated and tied to the same VIN.
Plan destination operation
Estimate cabin-energy demand and confirm refrigerant, filters, diagnostics and component support locally.
Replacement rule. Keep route reserve separate from brochure range. A substitute must repeat every check for plan destination operation. Similar colour, mileage or trim cannot transfer the previous VIN’s conclusion about plan destination operation to another vehicle.
Cold air is not a complete test
Sustained response, airflow, modes, warnings, drains and history also matter.
Powertrain state changes the result
Record whether the engine, battery and thermal systems were active during the test.
A recharge is not leak diagnosis
Request the cause and repeat evidence after repair.
Climate load belongs in route planning
Cabin demand can materially change electric reserve in difficult weather.
Primary model and market references
Official sources describe their own publication date and market. Confirm the selected VIN before applying a figure.
Close the file without hiding open items.
Close “Test Bao 5 Cabin Climate and Thermal Performance” with the candidate VIN, source date and the evidence used for identify installed equipment and record test conditions. Name rejected alternatives and unresolved questions, then assign responsibility for review diagnostics and repair and plan destination operation. A changed vehicle or destination reopens the affected checks.
- Identify installed equipment: confirmed / open / not applicable
- Record test conditions: confirmed / open / not applicable
- Test airflow and controls: confirmed / open / not applicable
- Test cooling and heating: confirmed / open / not applicable
- Review diagnostics and repair: confirmed / open / not applicable
- Plan destination operation: confirmed / open / not applicable
Three questions before commitment
What closes “Identify installed equipment”?
Do not copy equipment from another Bao 5 edition. For identify installed equipment, attach a dated source and candidate identifier, then name who produced or verified the record. A listing label is not enough to close this checkpoint.
What closes “Record test conditions”?
Make the result repeatable. Mark record test conditions as confirmed only when the supporting record matches the VIN and route assumptions. Otherwise show the item as open in the quotation or inspection scope.
What closes “Test airflow and controls”?
Separate control behaviour from temperature performance. If records about test airflow and controls conflict, preserve both sources and ask the responsible party to resolve the difference before deposit, preparation or shipping instructions.